Orem, Utah+1-253-294-9359info@waterdamagerestorationoremut.usServing Orem and Nearby Cities
Home / Services / Water Extraction
Orem, UT

Water Extraction in Orem, UT

Standing water, squishy carpet, a wet basement floor: extraction is the step where the water physically leaves the building. Here is what it involves, and how to tell whether it is a job for a wet vac or a crew.

What water extraction is, and what it isn't

Extraction means removing liquid water: the pooled water on the floor and the water held in carpet and pad, using pumps and extractors. It should happen as soon as the source is stopped, because every hour water sits, more of it wicks into drywall, baseboards and subfloor.

It isn't drying. Once the floor looks clear, the building materials still hold moisture you can't see, which is why extraction is normally followed by structural drying with air movers and dehumidifiers.

How the work usually goes

  1. Make it safe. Shut off the water source if you can. If water reached outlets, appliances or the panel, the power to that area needs to be off before anyone steps in.
  2. Work out what kind of water it is. A broken supply line is treated differently from water that came up a floor drain or in from outside, and that decision affects what can be saved.
  3. Pump or extract the bulk water. Submersible pumps handle several inches of water; truck-mounted or portable extractors pull water out of carpet and flooring.
  4. Deal with the carpet pad. Pad acts like a sponge and is usually cheaper to replace than to dry, so it is commonly removed even when the carpet above it can be saved.
  5. Check where the water went. Moisture meters and a thermal camera show wet drywall, insulation and framing that look fine from the surface.
  6. Move to a drying plan, or a cleanup plan if the water wasn't clean.

Wet vac or professional?

A shop vac is fine for a few gallons of clean water on a hard floor, like a dishwasher leak you caught early. It's the wrong tool once water covers most of a room, once it has soaked into carpet over a large area, or once you can't be sure the water is clean. Never run a household vacuum or any plugged-in equipment while standing in water.

What affects the price

  • How much water there is and how deep it is
  • Square footage affected
  • The kind of water (clean, gray or contaminated)
  • Flooring: carpet and pad, tile, hardwood, laminate
  • Access, such as basement stairs or tight crawl spaces
  • How long the water has been sitting
  • Whether drying and cleanup follow

We don't publish a price list because a number that ignores your actual space wouldn't be honest. A written estimate after someone looks at the damage is the only figure worth trusting.

Extraction in Orem homes

Utah homes with finished basements are where extraction jobs tend to run deepest. A failed sump pump, a window well that fills during a storm, or a water heater that lets go can put water across an entire lower level, and carpet, framing and insulation all get wet at once. Frozen pipe breaks upstairs after a hard cold snap send water down through floors into the rooms below.

Mistakes that make it worse

  • Waiting until morning to see whether it "dries on its own"
  • Running a fan and nothing else
  • Leaving soaked carpet pad under carpet to dry
  • Walking through water that might be contaminated

Common questions about water extraction

Can I extract water myself with a wet/dry vac?

For a small, clean spill, yes. For anything that covers a room, has soaked into carpet, or came from a dirty source, you'll leave a lot of water behind and take on health and electrical risks. If you're unsure, ask for an assessment.

How long does water extraction take?

A small area can take a couple of hours. A whole basement takes longer. The bigger timeline is the drying that follows, which is usually counted in days.

Do I have to throw out the carpet?

Not always. Carpet from a clean-water leak can often be extracted and dried in place, though the pad under it is commonly replaced. If the water was contaminated, carpet usually goes.

Is extraction enough to prevent mold?

Not on its own. Mold needs moisture and time, and materials that look dry can still be damp. Extraction removes the bulk water; drying and moisture checks deal with what's left.

What if the water came from a sewer backup?

Treat it as contaminated: keep kids and pets out and don't clean it yourself. See our sewage cleanup page. Extraction in that case is followed by disinfecting and removing porous materials.

Related services

Call NowFree Estimate